+++ /dev/null
-/*
- * Silicon Laboratories CP210x USB to RS232 serial adaptor driver
- *
- * Copyright (C) 2005 Craig Shelley (craig@microtron.org.uk)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License version
- * 2 as published by the Free Software Foundation.
- *
- * Support to set flow control line levels using TIOCMGET and TIOCMSET
- * thanks to Karl Hiramoto karl@hiramoto.org. RTSCTS hardware flow
- * control thanks to Munir Nassar nassarmu@real-time.com
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/slab.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/usb.h>
-#include <linux/uaccess.h>
-#include <linux/usb/serial.h>
-#include "cp210x.h"
-
-/*
- * Version Information
- */
-#define DRIVER_VERSION "vxxDEBVERxx"
-#define DRIVER_DESC "Silicon Labs CP210x RS232 serial adaptor driver"
-
-/*
- * Function Prototypes
- */
-static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *);
-static void cp210x_close(struct usb_serial_port *);
-static void cp210x_get_termios(struct tty_struct *,
- struct usb_serial_port *port);
-static void cp210x_get_termios_port(struct usb_serial_port *port,
- unsigned int *cflagp, unsigned int *baudp);
-static void cp210x_set_termios(struct tty_struct *, struct usb_serial_port *,
- struct ktermios*);
-static int cp210x_tiocmget(struct tty_struct *, struct file *);
-static int cp210x_tiocmset(struct tty_struct *, struct file *,
- unsigned int, unsigned int);
-static int cp210x_tiocmset_port(struct usb_serial_port *port, struct file *,
- unsigned int, unsigned int);
-static void cp210x_break_ctl(struct tty_struct *, int);
-static int cp210x_startup(struct usb_serial *);
-static int cp210x_ioctl(struct tty_struct *, struct file *,
- unsigned int, unsigned long);
-static void cp210x_dtr_rts(struct usb_serial_port *p, int on);
-static int cp210x_carrier_raised(struct usb_serial_port *p);
-
-static int debug;
-
-static const struct usb_device_id id_table[] = {
- { USB_DEVICE(0x0471, 0x066A) }, /* AKTAKOM ACE-1001 cable */
- { USB_DEVICE(0x0489, 0xE000) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
- { USB_DEVICE(0x0745, 0x1000) }, /* CipherLab USB CCD Barcode Scanner 1000 */
- { USB_DEVICE(0x08e6, 0x5501) }, /* Gemalto Prox-PU/CU contactless smartcard reader */
- { USB_DEVICE(0x08FD, 0x000A) }, /* Digianswer A/S , ZigBee/802.15.4 MAC Device */
- { USB_DEVICE(0x0BED, 0x1100) }, /* MEI (TM) Cashflow-SC Bill/Voucher Acceptor */
- { USB_DEVICE(0x0BED, 0x1101) }, /* MEI series 2000 Combo Acceptor */
- { USB_DEVICE(0x0FCF, 0x1003) }, /* Dynastream ANT development board */
- { USB_DEVICE(0x0FCF, 0x1004) }, /* Dynastream ANT2USB */
- { USB_DEVICE(0x0FCF, 0x1006) }, /* Dynastream ANT development board */
- { USB_DEVICE(0x10A6, 0xAA26) }, /* Knock-off DCU-11 cable */
- { USB_DEVICE(0x10AB, 0x10C5) }, /* Siemens MC60 Cable */
- { USB_DEVICE(0x10B5, 0xAC70) }, /* Nokia CA-42 USB */
- { USB_DEVICE(0x10C4, 0x0F91) }, /* Vstabi */
- { USB_DEVICE(0x10C4, 0x1101) }, /* Arkham Technology DS101 Bus Monitor */
- { USB_DEVICE(0x10C4, 0x1601) }, /* Arkham Technology DS101 Adapter */
- { USB_DEVICE(0x10C4, 0x800A) }, /* SPORTident BSM7-D-USB main station */
- { USB_DEVICE(0x10C4, 0x803B) }, /* Pololu USB-serial converter */
- { USB_DEVICE(0x10C4, 0x8044) }, /* Cygnal Debug Adapter */
- { USB_DEVICE(0x10C4, 0x804E) }, /* Software Bisque Paramount ME build-in converter */
- { USB_DEVICE(0x10C4, 0x8053) }, /* Enfora EDG1228 */
- { USB_DEVICE(0x10C4, 0x8054) }, /* Enfora GSM2228 */
- { USB_DEVICE(0x10C4, 0x8066) }, /* Argussoft In-System Programmer */
- { USB_DEVICE(0x10C4, 0x806F) }, /* IMS USB to RS422 Converter Cable */
- { USB_DEVICE(0x10C4, 0x807A) }, /* Crumb128 board */
- { USB_DEVICE(0x10C4, 0x80CA) }, /* Degree Controls Inc */
- { USB_DEVICE(0x10C4, 0x80DD) }, /* Tracient RFID */
- { USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */
- { USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */
- { USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */
- { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */
- { USB_DEVICE(0x10C4, 0x8149) }, /* West Mountain Radio Computerized Battery Analyzer */
- { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */
- { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */
- { USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */
- { USB_DEVICE(0x10C4, 0x818B) }, /* AVIT Research USB to TTL */
- { USB_DEVICE(0x10C4, 0x819F) }, /* MJS USB Toslink Switcher */
- { USB_DEVICE(0x10C4, 0x81A6) }, /* ThinkOptics WavIt */
- { USB_DEVICE(0x10C4, 0x81AC) }, /* MSD Dash Hawk */
- { USB_DEVICE(0x10C4, 0x81AD) }, /* INSYS USB Modem */
- { USB_DEVICE(0x10C4, 0x81C8) }, /* Lipowsky Industrie Elektronik GmbH, Baby-JTAG */
- { USB_DEVICE(0x10C4, 0x81E2) }, /* Lipowsky Industrie Elektronik GmbH, Baby-LIN */
- { USB_DEVICE(0x10C4, 0x81E7) }, /* Aerocomm Radio */
- { USB_DEVICE(0x10C4, 0x81E8) }, /* Zephyr Bioharness */
- { USB_DEVICE(0x10C4, 0x81F2) }, /* C1007 HF band RFID controller */
- { USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */
- { USB_DEVICE(0x10C4, 0x822B) }, /* Modem EDGE(GSM) Comander 2 */
- { USB_DEVICE(0x10C4, 0x826B) }, /* Cygnal Integrated Products, Inc., Fasttrax GPS demostration module */
- { USB_DEVICE(0x10C4, 0x8293) }, /* Telegesys ETRX2USB */
- { USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */
- { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */
- { USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */
- { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */
- { USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */
- { USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */
- { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
- { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
- { USB_DEVICE(0x10C4, 0xEA71) }, /* Infinity GPS-MIC-1 Radio Monophone */
- { USB_DEVICE(0x10C4, 0xF001) }, /* Elan Digital Systems USBscope50 */
- { USB_DEVICE(0x10C4, 0xF002) }, /* Elan Digital Systems USBwave12 */
- { USB_DEVICE(0x10C4, 0xF003) }, /* Elan Digital Systems USBpulse100 */
- { USB_DEVICE(0x10C4, 0xF004) }, /* Elan Digital Systems USBcount50 */
- { USB_DEVICE(0x10C5, 0xEA61) }, /* Silicon Labs MobiData GPRS USB Modem */
- { USB_DEVICE(0x10CE, 0xEA6A) }, /* Silicon Labs MobiData GPRS USB Modem 100EU */
- { USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
- { USB_DEVICE(0x1555, 0x0004) }, /* Owen AC4 USB-RS485 Converter */
- { USB_DEVICE(0x166A, 0x0303) }, /* Clipsal 5500PCU C-Bus USB interface */
- { USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */
- { USB_DEVICE(0x17F4, 0xAAAA) }, /* Wavesense Jazz blood glucose meter */
- { USB_DEVICE(0x1843, 0x0200) }, /* Vaisala USB Instrument Cable */
- { USB_DEVICE(0x18EF, 0xE00F) }, /* ELV USB-I2C-Interface */
- { USB_DEVICE(0x413C, 0x9500) }, /* DW700 GPS USB interface */
- { } /* Terminating Entry */
-};
-
-MODULE_DEVICE_TABLE(usb, id_table);
-
-static struct usb_driver cp210x_driver = {
- .name = "cp210x",
- .probe = usb_serial_probe,
- .disconnect = usb_serial_disconnect,
- .id_table = id_table,
- .no_dynamic_id = 1,
-};
-
-static struct usb_serial_driver cp210x_device = {
- .driver = {
- .owner = THIS_MODULE,
- .name = "cp210x",
- },
- .usb_driver = &cp210x_driver,
- .id_table = id_table,
- .num_ports = 1,
- .bulk_in_size = 256,
- .bulk_out_size = 256,
- .open = cp210x_open,
- .close = cp210x_close,
- .ioctl = cp210x_ioctl,
- .break_ctl = cp210x_break_ctl,
- .set_termios = cp210x_set_termios,
- .tiocmget = cp210x_tiocmget,
- .tiocmset = cp210x_tiocmset,
- .attach = cp210x_startup,
- .dtr_rts = cp210x_dtr_rts,
- .carrier_raised = cp210x_carrier_raised
-};
-
-/* Config request codes */
-#define CP210X_IFC_ENABLE 0x00
-#define CP210X_SET_BAUDDIV 0x01
-#define CP210X_GET_BAUDDIV 0x02
-#define CP210X_SET_LINE_CTL 0x03
-#define CP210X_GET_LINE_CTL 0x04
-#define CP210X_SET_BREAK 0x05
-#define CP210X_IMM_CHAR 0x06
-#define CP210X_SET_MHS 0x07
-#define CP210X_GET_MDMSTS 0x08
-#define CP210X_SET_XON 0x09
-#define CP210X_SET_XOFF 0x0A
-#define CP210X_SET_EVENTMASK 0x0B
-#define CP210X_GET_EVENTMASK 0x0C
-#define CP210X_SET_CHAR 0x0D
-#define CP210X_GET_CHARS 0x0E
-#define CP210X_GET_PROPS 0x0F
-#define CP210X_GET_COMM_STATUS 0x10
-#define CP210X_RESET 0x11
-#define CP210X_PURGE 0x12
-#define CP210X_SET_FLOW 0x13
-#define CP210X_GET_FLOW 0x14
-#define CP210X_EMBED_EVENTS 0x15
-#define CP210X_GET_EVENTSTATE 0x16
-#define CP210X_SET_CHARS 0x19
-
-/* CP210X_IFC_ENABLE */
-#define UART_ENABLE 0x0001
-#define UART_DISABLE 0x0000
-
-/* CP210X_(SET|GET)_BAUDDIV */
-#define BAUD_RATE_GEN_FREQ 0x384000
-
-/* CP210X_(SET|GET)_LINE_CTL */
-#define BITS_DATA_MASK 0X0f00
-#define BITS_DATA_5 0X0500
-#define BITS_DATA_6 0X0600
-#define BITS_DATA_7 0X0700
-#define BITS_DATA_8 0X0800
-#define BITS_DATA_9 0X0900
-
-#define BITS_PARITY_MASK 0x00f0
-#define BITS_PARITY_NONE 0x0000
-#define BITS_PARITY_ODD 0x0010
-#define BITS_PARITY_EVEN 0x0020
-#define BITS_PARITY_MARK 0x0030
-#define BITS_PARITY_SPACE 0x0040
-
-#define BITS_STOP_MASK 0x000f
-#define BITS_STOP_1 0x0000
-#define BITS_STOP_1_5 0x0001
-#define BITS_STOP_2 0x0002
-
-/* CP210X_SET_BREAK */
-#define BREAK_ON 0x0000
-#define BREAK_OFF 0x0001
-
-/* CP210X_(SET_MHS|GET_MDMSTS) */
-#define CONTROL_DTR 0x0001
-#define CONTROL_RTS 0x0002
-#define CONTROL_CTS 0x0010
-#define CONTROL_DSR 0x0020
-#define CONTROL_RING 0x0040
-#define CONTROL_DCD 0x0080
-#define CONTROL_WRITE_DTR 0x0100
-#define CONTROL_WRITE_RTS 0x0200
-
-/* cp210x_get_partnum() return codes */
-#define CP210x_PART_UNKNOWN 0x00
-#define CP210x_PART_CP2101 0x01
-#define CP210x_PART_CP2102 0x02
-#define CP210x_PART_CP2103 0x03
-
-/* Taken from drivers/usb/gadget/usbstring.c */
-static int utf8_to_utf16le(const char *s, __le16 *cp, unsigned len)
-{
- int count = 0;
- u8 c;
- u16 uchar;
-
- /* this insists on correct encodings, though not minimal ones.
- * BUT it currently rejects legit 4-byte UTF-8 code points,
- * which need surrogate pairs. (Unicode 3.1 can use them.)
- */
- while (len != 0 && (c = (u8) *s++) != 0) {
- if (unlikely(c & 0x80)) {
- // 2-byte sequence:
- // 00000yyyyyxxxxxx = 110yyyyy 10xxxxxx
- if ((c & 0xe0) == 0xc0) {
- uchar = (c & 0x1f) << 6;
-
- c = (u8) *s++;
- if ((c & 0xc0) != 0x80)
- goto fail;
- c &= 0x3f;
- uchar |= c;
-
- // 3-byte sequence (most CJKV characters):
- // zzzzyyyyyyxxxxxx = 1110zzzz 10yyyyyy 10xxxxxx
- } else if ((c & 0xf0) == 0xe0) {
- uchar = (c & 0x0f) << 12;
-
- c = (u8) *s++;
- if ((c & 0xc0) != 0x80)
- goto fail;
- c &= 0x3f;
- uchar |= c << 6;
-
- c = (u8) *s++;
- if ((c & 0xc0) != 0x80)
- goto fail;
- c &= 0x3f;
- uchar |= c;
-
- /* no bogus surrogates */
- if (0xd800 <= uchar && uchar <= 0xdfff)
- goto fail;
-
- // 4-byte sequence (surrogate pairs, currently rare):
- // 11101110wwwwzzzzyy + 110111yyyyxxxxxx
- // = 11110uuu 10uuzzzz 10yyyyyy 10xxxxxx
- // (uuuuu = wwww + 1)
- // FIXME accept the surrogate code points (only)
-
- } else
- goto fail;
- } else
- uchar = c;
- *cp++ = uchar;
- count++;
- len--;
- }
- return count;
-fail:
- return -1;
-}
-
-
-/*
- * make_usb_string
- * Populates usbstr with: (len) + (USB_DT_STRING) + unicode(str). Each char in
- * usbstr consumes two bytes in unicode (__le16) format.
- * Returns the resulting length of usbstr in bytes.
- * This function can accept overlapping usbstr and str as long as the overlap
- * does not cause data written to usbstr to overwrite data not yet read from
- * str.
- */
-static int make_usb_string(__le16* usbstr, size_t usblen, const char *src,
- size_t srclen)
-{
- int len;
-
- /* string descriptors have length, type, then UTF16-LE text */
- if (usblen > 254)
- usblen = 254;
- len = min(usblen / 2 - 1, srclen);
- len = utf8_to_utf16le(src, usbstr + 1, len);
- if (len >= 0) {
- len = (len + 1) * 2;
- ((u8 *)usbstr)[0] = len;
- ((u8 *)usbstr)[1] = USB_DT_STRING;
- }
- return len;
-}
-
-/*
- * cp210x_usbstr_from_user
- * Populate kbuf with a usb string derived from a user space variable. klen
- * is the size of the buffer at kbuf.
- * Returns the number of bytes used in kbuf.
- */
-static size_t cp210x_usbstr_from_user(__le16 *kbuf,
- struct cp210x_buffer __user *ubuf, size_t klen)
-{
- struct cp210x_buffer t;
- char *str;
- size_t slen;
-
- if (copy_from_user(&t, ubuf, sizeof(t)))
- return -EINVAL;
- slen = klen / 2 - 1;
- if (!t.buf || !t.len || t.len > slen)
- return -EINVAL;
- if (t.len < slen)
- slen = t.len;
- str = (char *)kbuf + klen - slen;
- if (copy_from_user(str, (__u8 __user *)t.buf, slen))
- return -EINVAL;
- return make_usb_string(kbuf, klen, str, slen);
-}
-
-/*
- * cp210x_ctlmsg
- * A generic usb control message interface.
- * Returns the actual size of the data read or written within the message, 0
- * if no data were read or written, or a negative value to indicate an error.
- */
-static int cp210x_ctlmsg(struct usb_serial_port *port, u8 request,
- u8 requestype, u16 value, u16 index, void *data, u16 size)
-{
- struct usb_device *dev = port->serial->dev;
- u8 *tbuf;
- int ret;
-
- tbuf = kmalloc(size, GFP_KERNEL);
- if (!tbuf)
- return -ENOMEM;
- if (requestype & USB_DIR_IN) {
- ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), request,
- requestype, value, index, tbuf, size, 300);
- if (ret > 0 && size)
- memcpy(data, tbuf, size);
- } else {
- if (size)
- memcpy(tbuf, data, size);
- ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), request,
- requestype, value, index, tbuf, size, 300);
- }
- kfree(tbuf);
- if (ret < 0 && ret != -EPIPE) {
- dev_printk(KERN_DEBUG, &dev->dev,
- "cp210x: ctl failed cmd rqt %u rq %u len %u ret %d\n",
- requestype, request, size, ret);
- }
- return ret;
-}
-
-static int cp210x_reset(struct usb_serial_port *port)
-{
- dbg("%s", __func__);
-
- /* Instructing the CP210X to reset seems to work more reliably than
- * calling usb_reset_device().
- */
- cp210x_ctlmsg(port, 0xff, USB_TYPE_VENDOR,
- 0x0008, 0x00, NULL, 0);
- return 0;
-}
-
-static int cp210x_get_partnum(struct usb_serial_port *port)
-{
- static u8 _partnum = CP210x_PART_UNKNOWN;
-
- if (_partnum == CP210x_PART_UNKNOWN) {
- u8 addr = port->serial->dev->actconfig->interface[0]->
- cur_altsetting->endpoint[0].desc.bEndpointAddress &
- USB_ENDPOINT_NUMBER_MASK;
-
- if (addr == 0x03 || addr == 0x02)
- _partnum = CP210x_PART_CP2101;
- else if (addr == 0x01) {
- /* Must query part to determine part number */
- if (cp210x_ctlmsg(port, 0xff,
- USB_DIR_IN|USB_TYPE_VENDOR,
- 0x370b, 0x00, &_partnum, 1) != 1)
- _partnum = CP210x_PART_UNKNOWN;
- }
- }
- dbg("%s - partnum %u", __func__, _partnum);
- return _partnum;
-}
-
-static inline int cp210x_setu16(struct usb_serial_port *port, int cmd,
- unsigned int value)
-{
- return cp210x_ctlmsg(port, 0xff, USB_TYPE_VENDOR,
- 0x3700 | (cmd & 0xff), value, NULL, 0);
-}
-
-/*
- * cp210x_setstr
- *
- * Set a USB string descriptor using proprietary cp210x control messages.
- * Return the number of characters actually written.
- */
-static int cp210x_setstr(struct usb_serial_port *port, int cmd, __le16 *usbstr)
-{
- int len = ((u8 *)usbstr)[0];
- int ret = cp210x_ctlmsg(port, 0xff, USB_TYPE_VENDOR,
- 0x3700 | (cmd & 0xff), 0, usbstr, len);
- dbg("%s - cmd 0x%02x len %d ret %d", __func__, cmd, len, ret);
- return ret;
-}
-
-/* Set all gpio simultaneously */
-static int cp210x_gpioset(struct usb_serial_port *port, u8 gpio)
-{
- dbg("%s - port %d, gpio = 0x%.2x", __func__, port->number, gpio);
-
- return cp210x_ctlmsg(port, 0xff, USB_TYPE_VENDOR,
- 0x37e1, ((uint16_t)gpio << 8) | GPIO_MASK, NULL, 0);
-}
-
-/* Set select gpio bits */
-static int cp210x_gpiosetb(struct usb_serial_port *port, u8 set, u8 clear)
-{
- u16 gpio = 0;
-
- /* The bitmask is in the LSB, the values in the MSB */
- if (set & GPIO_0)
- gpio |= (GPIO_0 << 8)|GPIO_0;
- if (set & GPIO_1)
- gpio |= (GPIO_1 << 8)|GPIO_1;
- if (set & GPIO_2)
- gpio |= (GPIO_2 << 8)|GPIO_2;
- if (set & GPIO_3)
- gpio |= (GPIO_3 << 8)|GPIO_3;
- if (clear & GPIO_0)
- gpio = (gpio & ~(GPIO_0 << 8))|GPIO_0;
- if (clear & GPIO_1)
- gpio = (gpio & ~(GPIO_1 << 8))|GPIO_1;
- if (clear & GPIO_2)
- gpio = (gpio & ~(GPIO_2 << 8))|GPIO_2;
- if (clear & GPIO_3)
- gpio = (gpio & ~(GPIO_3 << 8))|GPIO_3;
-
- dbg("%s - port %d, gpiob = 0x%.4x", __func__, port->number, gpio);
-
- return cp210x_ctlmsg(port, 0xff, USB_TYPE_VENDOR,
- 0x37e1, gpio, NULL, 0);
-}
-
-static int cp210x_gpioget(struct usb_serial_port *port, u8 *gpio)
-{
- int ret;
-
- dbg("%s - port %d", __func__, port->number);
-
- ret = cp210x_ctlmsg(port, 0xff, USB_DIR_IN|USB_TYPE_VENDOR,
- 0x00c2, 0, gpio, 1);
-
- dbg("%s - gpio = 0x%.2x (%d)", __func__, *gpio, ret);
-
- return (ret == 1) ? 0 : -1;
-}
-
-static int cp210x_portconfset(struct usb_serial_port *port,
- struct cp210x_port_config *config)
-{
- struct cp210x_port_config lconfig;
- int ret;
-
- dbg("%s", __func__);
-
- memcpy(&lconfig, config, sizeof(lconfig));
-
- /* Words from cp210x are MSB */
- lconfig.reset.mode = cpu_to_be16(config->reset.mode);
- lconfig.reset.latch = cpu_to_be16(config->reset.latch);
- lconfig.suspend.mode = cpu_to_be16(config->suspend.mode);
- lconfig.suspend.latch = cpu_to_be16(config->suspend.latch);
- /* apparently not implemented by CP210X firmware */
- lconfig.suspend.lowPower = 0;
- lconfig.reset.lowPower = 0;
-
- ret = cp210x_ctlmsg(port, 0xff, USB_TYPE_VENDOR, 0x370c,
- 0, &lconfig, sizeof(struct cp210x_port_config));
- if (ret == sizeof(struct cp210x_port_config))
- return 0;
- else if (ret >= 0)
- return -1;
- else
- return ret;
-}
-
-static int cp210x_portconfget(struct usb_serial_port *port,
- struct cp210x_port_config *config)
-{
- int ret;
-
- dbg("%s", __func__);
-
- ret = cp210x_ctlmsg(port, 0xff, USB_DIR_IN|USB_TYPE_VENDOR,
- 0x370c, 0, config, sizeof(struct cp210x_port_config));
- if (ret == sizeof(struct cp210x_port_config)) {
- /* Words from cp210x are MSB */
- config->reset.mode = be16_to_cpu(config->reset.mode);
- config->reset.lowPower = be16_to_cpu(config->reset.lowPower);
- config->reset.latch = be16_to_cpu(config->reset.latch);
- config->suspend.mode = be16_to_cpu(config->suspend.mode);
- config->suspend.lowPower =
- be16_to_cpu(config->suspend.lowPower);
- config->suspend.latch = be16_to_cpu(config->suspend.latch);
-
- /* apparently not implemented yet */
- config->reset.lowPower = 0;
- config->suspend.lowPower = 0;
-
- return 0;
- } else if (ret >= 0)
- return -1;
- else
- return ret;
-
-}
-
-/*
- * cp210x_get_config
- * Reads from the CP210x configuration registers
- * 'size' is specified in bytes.
- * 'data' is a pointer to a pre-allocated array of integers large
- * enough to hold 'size' bytes (with 4 bytes to each integer)
- */
-static int cp210x_get_config(struct usb_serial_port *port, u8 request,
- unsigned int *data, int size)
-{
- struct usb_serial *serial = port->serial;
- __le32 *buf;
- int result, i, length;
-
- /* Number of integers required to contain the array */
- length = (((size - 1) | 3) + 1)/4;
-
- buf = kcalloc(length, sizeof(__le32), GFP_KERNEL);
- if (!buf) {
- dev_err(&port->dev, "%s - out of memory.\n", __func__);
- return -ENOMEM;
- }
-
- /* Issue the request, attempting to read 'size' bytes */
- result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
- request,
- USB_DIR_IN|USB_TYPE_VENDOR|USB_RECIP_INTERFACE,
- 0x0000, 0, buf, size, 300);
-
- /* Convert data into an array of integers */
- for (i = 0; i < length; i++)
- data[i] = le32_to_cpu(buf[i]);
-
- kfree(buf);
-
- if (result != size) {
- dbg("%s - Unable to send config request, "
- "request=0x%x size=%d result=%d\n",
- __func__, request, size, result);
- return -EPROTO;
- }
-
- return 0;
-}
-
-/*
- * cp210x_set_config
- * Writes to the CP210x configuration registers
- * Values less than 16 bits wide are sent directly
- * 'size' is specified in bytes.
- */
-static int cp210x_set_config(struct usb_serial_port *port, u8 request,
- unsigned int *data, int size)
-{
- struct usb_serial *serial = port->serial;
- __le32 *buf;
- int result, i, length;
-
- /* Number of integers required to contain the array */
- length = (((size - 1) | 3) + 1)/4;
-
- buf = kmalloc(length * sizeof(__le32), GFP_KERNEL);
- if (!buf) {
- dev_err(&port->dev, "%s - out of memory.\n",
- __func__);
- return -ENOMEM;
- }
-
- /* Array of integers into bytes */
- for (i = 0; i < length; i++)
- buf[i] = cpu_to_le32(data[i]);
-
- if (size > 2) {
- result = usb_control_msg(serial->dev,
- usb_sndctrlpipe(serial->dev, 0), request,
- USB_TYPE_VENDOR|USB_RECIP_INTERFACE, 0x0000,
- 0, buf, size, 300);
- } else {
- result = usb_control_msg(serial->dev,
- usb_sndctrlpipe(serial->dev, 0), request,
- USB_TYPE_VENDOR|USB_RECIP_INTERFACE, data[0],
- 0, NULL, 0, 300);
- }
-
- kfree(buf);
-
- if ((size > 2 && result != size) || result < 0) {
- dbg("%s - Unable to send request, "
- "request=0x%x size=%d result=%d\n",
- __func__, request, size, result);
- return -EPROTO;
- }
-
- return 0;
-}
-
-/*
- * cp210x_set_config_single
- * Convenience function for calling cp210x_set_config on single data values
- * without requiring an integer pointer
- */
-static inline int cp210x_set_config_single(struct usb_serial_port *port,
- u8 request, unsigned int data)
-{
- return cp210x_set_config(port, request, &data, 2);
-}
-
-/*
- * cp210x_quantise_baudrate
- * Quantises the baud rate as per AN205 Table 1
- */
-static unsigned int cp210x_quantise_baudrate(unsigned int baud) {
- if (baud <= 56) baud = 0;
- else if (baud <= 300) baud = 300;
- else if (baud <= 600) baud = 600;
- else if (baud <= 1200) baud = 1200;
- else if (baud <= 1800) baud = 1800;
- else if (baud <= 2400) baud = 2400;
- else if (baud <= 4000) baud = 4000;
- else if (baud <= 4803) baud = 4800;
- else if (baud <= 7207) baud = 7200;
- else if (baud <= 9612) baud = 9600;
- else if (baud <= 14428) baud = 14400;
- else if (baud <= 16062) baud = 16000;
- else if (baud <= 19250) baud = 19200;
- else if (baud <= 28912) baud = 28800;
- else if (baud <= 38601) baud = 38400;
- else if (baud <= 51558) baud = 51200;
- else if (baud <= 56280) baud = 56000;
- else if (baud <= 58053) baud = 57600;
- else if (baud <= 64111) baud = 64000;
- else if (baud <= 77608) baud = 76800;
- else if (baud <= 117028) baud = 115200;
- else if (baud <= 129347) baud = 128000;
- else if (baud <= 156868) baud = 153600;
- else if (baud <= 237832) baud = 230400;
- else if (baud <= 254234) baud = 250000;
- else if (baud <= 273066) baud = 256000;
- else if (baud <= 491520) baud = 460800;
- else if (baud <= 567138) baud = 500000;
- else if (baud <= 670254) baud = 576000;
- else if (baud <= 1053257) baud = 921600;
- else if (baud <= 1474560) baud = 1228800;
- else if (baud <= 2457600) baud = 1843200;
- else baud = 3686400;
- return baud;
-}
-
-static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port)
-{
- int result;
-
- dbg("%s - port %d", __func__, port->number);
-
- if (cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_ENABLE)) {
- dev_err(&port->dev, "%s - Unable to enable UART\n",
- __func__);
- return -EPROTO;
- }
-
- result = usb_serial_generic_open(tty, port);
- if (result)
- return result;
-
- /* Configure the termios structure */
- cp210x_get_termios(tty, port);
- return 0;
-}
-
-static void cp210x_close(struct usb_serial_port *port)
-{
- dbg("%s - port %d", __func__, port->number);
-
- usb_serial_generic_close(port);
-
- mutex_lock(&port->serial->disc_mutex);
- if (!port->serial->disconnected)
- cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_DISABLE);
- mutex_unlock(&port->serial->disc_mutex);
-}
-
-static int cp210x_ioctl(struct tty_struct *tty, struct file *file,
- unsigned int cmd, unsigned long arg)
-{
- struct usb_serial_port *port = tty->driver_data;
-
- dbg("%s (%d) cmd = 0x%04x", __func__, port->number, cmd);
-
- switch (cmd) {
-
- case TIOCMGET:
- {
- int result = cp210x_tiocmget(tty, file);
- if (copy_to_user((int __user *)&arg, &result, sizeof(int)))
- return -EFAULT;
- return 0;
- }
- break;
-
- case TIOCMSET:
- case TIOCMBIS:
- case TIOCMBIC:
- {
- int val = 0;
-
- if (copy_from_user(&val, (int __user *)&arg, sizeof(int)))
- return -EFAULT;
-
- /* this looks wrong: TIOCMSET isn't going to work right */
- if (cp210x_tiocmset(tty, file, (cmd == TIOCMBIC) ? 0 : val,
- (cmd == TIOCMBIC) ? val : 0))
- return -EFAULT;
- return 0;
- }
- break;
-
- case CP210x_IOCTL_GPIOGET:
- if (cp210x_get_partnum(port) == CP210x_PART_CP2103) {
- u8 gpio = 0;
- if (!cp210x_gpioget(port, &gpio) && !copy_to_user(
- (__u8 __user *)arg, &gpio,
- sizeof(gpio)))
- return 0;
- }
- return -EFAULT;
- break;
-
- case CP210x_IOCTL_GPIOSET:
- if (cp210x_get_partnum(port) == CP210x_PART_CP2103 &&
- !cp210x_gpioset(port, arg))
- return 0;
- return -EFAULT;
- break;
-
- case CP210x_IOCTL_GPIOBIC:
- case CP210x_IOCTL_GPIOBIS:
- if (cp210x_get_partnum(port) == CP210x_PART_CP2103 &&
- !cp210x_gpiosetb(port,
- (cmd == CP210x_IOCTL_GPIOBIC) ? 0 : arg,
- (cmd == CP210x_IOCTL_GPIOBIC) ? arg : 0))
- return 0;
- return -EFAULT;
- break;
-
- case CP210x_IOCTL_DEVICERESET:
- return cp210x_reset(port);
- break;
-
- case CP210x_IOCTL_PORTCONFGET:
- {
- struct cp210x_port_config config;
- if (!cp210x_portconfget(port, &config) && !copy_to_user(
- (struct cp210x_port_config __user *)arg,
- &config, sizeof(config)))
- return 0;
- }
- return -EFAULT;
- break;
-
- case CP210x_IOCTL_PORTCONFSET:
- {
- struct cp210x_port_config config;
- if (!copy_from_user(&config, (struct cp210x_port_config __user *)arg,
- sizeof(config)) &&
- !cp210x_portconfset(port, &config))
- return 0;
- return -EFAULT;
- }
- break;
-
- case CP210x_IOCTL_SETVID:
- {
- unsigned int vid;
- if (!copy_from_user(&vid, (unsigned int __user *)arg,
- sizeof(unsigned int)) &&
- !cp210x_setu16(port, 0x01, vid))
- return 0;
- return -EFAULT;
- }
- break;
-
- case CP210x_IOCTL_SETPID:
- {
- unsigned int pid;
- if (!copy_from_user(&pid, (unsigned int __user *)arg,
- sizeof(unsigned int)) &&
- !cp210x_setu16(port, 0x02, pid))
- return 0;
- return -EFAULT;
- }
- break;
-
- case CP210x_IOCTL_SETPRODUCT:
- {
- __le16 usbstr[CP210x_MAX_PRODUCT_STRLEN + 1];
- size_t len = cp210x_usbstr_from_user(usbstr,
- (struct cp210x_buffer __user *)arg,
- sizeof(usbstr));
- if (len > 0 && cp210x_setstr(port, 0x03, usbstr) == len)
- return 0;
- return -EFAULT;
- }
- break;
-
- case CP210x_IOCTL_SETSERIAL:
- {
- __le16 usbstr[CP210x_MAX_SERIAL_STRLEN + 1];
- size_t len = cp210x_usbstr_from_user(usbstr,
- (struct cp210x_buffer __user *)arg,
- sizeof(usbstr));
- if (len > 0 && cp210x_setstr(port, 0x04, usbstr) == len)
- return 0;
- return -EFAULT;
- }
- break;
-
- case CP210x_IOCTL_SETDEVVER:
- {
- unsigned int ver;
- if (!copy_from_user(&ver, (unsigned int __user *)arg,
- sizeof(unsigned int)) &&
- !cp210x_setu16(port, 0x07, ver))
- return 0;
- return -EFAULT;
- }
- break;
-
- default:
- dbg("%s not supported = 0x%04x", __func__, cmd);
- break;
- }
-
- return -ENOIOCTLCMD;
-}
-
-/*
- * cp210x_get_termios
- * Reads the baud rate, data bits, parity, stop bits and flow control mode
- * from the device, corrects any unsupported values, and configures the
- * termios structure to reflect the state of the device
- */
-static void cp210x_get_termios(struct tty_struct *tty,
- struct usb_serial_port *port)
-{
- unsigned int baud;
-
- if (tty) {
- cp210x_get_termios_port(tty->driver_data,
- &tty->termios->c_cflag, &baud);
- tty_encode_baud_rate(tty, baud, baud);
- }
-
- else {
- unsigned int cflag;
- cflag = 0;
- cp210x_get_termios_port(port, &cflag, &baud);
- }
-}
-
-/*
- * cp210x_get_termios_port
- * This is the heart of cp210x_get_termios which always uses a &usb_serial_port.
- */
-static void cp210x_get_termios_port(struct usb_serial_port *port,
- unsigned int *cflagp, unsigned int *baudp)
-{
- unsigned int cflag, modem_ctl[4];
- unsigned int baud;
- unsigned int bits;
-
- dbg("%s - port %d", __func__, port->number);
-
- cp210x_get_config(port, CP210X_GET_BAUDDIV, &baud, 2);
- /* Convert to baudrate */
- if (baud)
- baud = cp210x_quantise_baudrate((BAUD_RATE_GEN_FREQ + baud/2)/ baud);
-
- dbg("%s - baud rate = %d", __func__, baud);
- *baudp = baud;
-
- cflag = *cflagp;
-
- cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
- cflag &= ~CSIZE;
- switch (bits & BITS_DATA_MASK) {
- case BITS_DATA_5:
- dbg("%s - data bits = 5", __func__);
- cflag |= CS5;
- break;
- case BITS_DATA_6:
- dbg("%s - data bits = 6", __func__);
- cflag |= CS6;
- break;
- case BITS_DATA_7:
- dbg("%s - data bits = 7", __func__);
- cflag |= CS7;
- break;
- case BITS_DATA_8:
- dbg("%s - data bits = 8", __func__);
- cflag |= CS8;
- break;
- case BITS_DATA_9:
- dbg("%s - data bits = 9 (not supported, using 8 data bits)",
- __func__);
- cflag |= CS8;
- bits &= ~BITS_DATA_MASK;
- bits |= BITS_DATA_8;
- cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
- break;
- default:
- dbg("%s - Unknown number of data bits, using 8", __func__);
- cflag |= CS8;
- bits &= ~BITS_DATA_MASK;
- bits |= BITS_DATA_8;
- cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
- break;
- }
-
- switch (bits & BITS_PARITY_MASK) {
- case BITS_PARITY_NONE:
- dbg("%s - parity = NONE", __func__);
- cflag &= ~PARENB;
- break;
- case BITS_PARITY_ODD:
- dbg("%s - parity = ODD", __func__);
- cflag |= (PARENB|PARODD);
- break;
- case BITS_PARITY_EVEN:
- dbg("%s - parity = EVEN", __func__);
- cflag &= ~PARODD;
- cflag |= PARENB;
- break;
- case BITS_PARITY_MARK:
- dbg("%s - parity = MARK (not supported, disabling parity)",
- __func__);
- cflag &= ~PARENB;
- bits &= ~BITS_PARITY_MASK;
- cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
- break;
- case BITS_PARITY_SPACE:
- dbg("%s - parity = SPACE (not supported, disabling parity)",
- __func__);
- cflag &= ~PARENB;
- bits &= ~BITS_PARITY_MASK;
- cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
- break;
- default:
- dbg("%s - Unknown parity mode, disabling parity", __func__);
- cflag &= ~PARENB;
- bits &= ~BITS_PARITY_MASK;
- cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
- break;
- }
-
- cflag &= ~CSTOPB;
- switch (bits & BITS_STOP_MASK) {
- case BITS_STOP_1:
- dbg("%s - stop bits = 1", __func__);
- break;
- case BITS_STOP_1_5:
- dbg("%s - stop bits = 1.5 (not supported, using 1 stop bit)",
- __func__);
- bits &= ~BITS_STOP_MASK;
- cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
- break;
- case BITS_STOP_2:
- dbg("%s - stop bits = 2", __func__);
- cflag |= CSTOPB;
- break;
- default:
- dbg("%s - Unknown number of stop bits, using 1 stop bit",
- __func__);
- bits &= ~BITS_STOP_MASK;
- cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
- break;
- }
-
- cp210x_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
- if (modem_ctl[0] & 0x0008) {
- dbg("%s - flow control = CRTSCTS", __func__);
- cflag |= CRTSCTS;
- } else {
- dbg("%s - flow control = NONE", __func__);
- cflag &= ~CRTSCTS;
- }
-
- *cflagp = cflag;
-}
-
-static void cp210x_set_termios(struct tty_struct *tty,
- struct usb_serial_port *port, struct ktermios *old_termios)
-{
- unsigned int cflag, old_cflag;
- unsigned int baud = 0, bits;
- unsigned int modem_ctl[4];
-
- dbg("%s - port %d", __func__, port->number);
-
- if (!tty)
- return;
-
- tty->termios->c_cflag &= ~CMSPAR;
- cflag = tty->termios->c_cflag;
- old_cflag = old_termios->c_cflag;
- baud = cp210x_quantise_baudrate(tty_get_baud_rate(tty));
-
- /* If the baud rate is to be updated*/
- if (baud != tty_termios_baud_rate(old_termios) && baud != 0) {
- dbg("%s - Setting baud rate to %d baud", __func__,
- baud);
- if (cp210x_set_config_single(port, CP210X_SET_BAUDDIV,
- ((BAUD_RATE_GEN_FREQ + baud/2) / baud))) {
- dbg("Baud rate requested not supported by device");
- baud = tty_termios_baud_rate(old_termios);
- }
- }
- /* Report back the resulting baud rate */
- tty_encode_baud_rate(tty, baud, baud);
-
- /* If the number of data bits is to be updated */
- if ((cflag & CSIZE) != (old_cflag & CSIZE)) {
- cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
- bits &= ~BITS_DATA_MASK;
- switch (cflag & CSIZE) {
- case CS5:
- bits |= BITS_DATA_5;
- dbg("%s - data bits = 5", __func__);
- break;
- case CS6:
- bits |= BITS_DATA_6;
- dbg("%s - data bits = 6", __func__);
- break;
- case CS7:
- bits |= BITS_DATA_7;
- dbg("%s - data bits = 7", __func__);
- break;
- case CS8:
- bits |= BITS_DATA_8;
- dbg("%s - data bits = 8", __func__);
- break;
- /*case CS9:
- bits |= BITS_DATA_9;
- dbg("%s - data bits = 9", __func__);
- break;*/
- default:
- dbg("cp210x driver does not "
- "support the number of bits requested,"
- " using 8 bit mode\n");
- bits |= BITS_DATA_8;
- break;
- }
- if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
- dbg("Number of data bits requested "
- "not supported by device\n");
- }
-
- if ((cflag & (PARENB|PARODD)) != (old_cflag & (PARENB|PARODD))) {
- cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
- bits &= ~BITS_PARITY_MASK;
- if (cflag & PARENB) {
- if (cflag & PARODD) {
- bits |= BITS_PARITY_ODD;
- dbg("%s - parity = ODD", __func__);
- } else {
- bits |= BITS_PARITY_EVEN;
- dbg("%s - parity = EVEN", __func__);
- }
- }
- if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
- dbg("Parity mode not supported "
- "by device\n");
- }
-
- if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
- cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
- bits &= ~BITS_STOP_MASK;
- if (cflag & CSTOPB) {
- bits |= BITS_STOP_2;
- dbg("%s - stop bits = 2", __func__);
- } else {
- bits |= BITS_STOP_1;
- dbg("%s - stop bits = 1", __func__);
- }
- if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
- dbg("Number of stop bits requested "
- "not supported by device\n");
- }
-
- if ((cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
- cp210x_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
- dbg("%s - read modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
- __func__, modem_ctl[0], modem_ctl[1],
- modem_ctl[2], modem_ctl[3]);
-
- if (cflag & CRTSCTS) {
- modem_ctl[0] &= ~0x7B;
- modem_ctl[0] |= 0x09;
- modem_ctl[1] = 0x80;
- dbg("%s - flow control = CRTSCTS", __func__);
- } else {
- modem_ctl[0] &= ~0x7B;
- modem_ctl[0] |= 0x01;
- modem_ctl[1] |= 0x40;
- dbg("%s - flow control = NONE", __func__);
- }
-
- dbg("%s - write modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
- __func__, modem_ctl[0], modem_ctl[1],
- modem_ctl[2], modem_ctl[3]);
- cp210x_set_config(port, CP210X_SET_FLOW, modem_ctl, 16);
- }
-
-}
-
-static int cp210x_tiocmset (struct tty_struct *tty, struct file *file,
- unsigned int set, unsigned int clear)
-{
- struct usb_serial_port *port = tty->driver_data;
- return cp210x_tiocmset_port(port, file, set, clear);
-}
-
-static int cp210x_tiocmset_port(struct usb_serial_port *port, struct file *file,
- unsigned int set, unsigned int clear)
-{
- unsigned int control = 0;
-
- dbg("%s - port %d", __func__, port->number);
-
- if (set & TIOCM_RTS) {
- control |= CONTROL_RTS;
- control |= CONTROL_WRITE_RTS;
- }
- if (set & TIOCM_DTR) {
- control |= CONTROL_DTR;
- control |= CONTROL_WRITE_DTR;
- }
- if (clear & TIOCM_RTS) {
- control &= ~CONTROL_RTS;
- control |= CONTROL_WRITE_RTS;
- }
- if (clear & TIOCM_DTR) {
- control &= ~CONTROL_DTR;
- control |= CONTROL_WRITE_DTR;
- }
-
- dbg("%s - control = 0x%.4x", __func__, control);
-
- return cp210x_set_config(port, CP210X_SET_MHS, &control, 2);
-}
-
-static void cp210x_dtr_rts(struct usb_serial_port *p, int on)
-{
- if (on)
- cp210x_tiocmset_port(p, NULL, TIOCM_DTR|TIOCM_RTS, 0);
- else
- cp210x_tiocmset_port(p, NULL, 0, TIOCM_DTR|TIOCM_RTS);
-}
-
-static int cp210x_tiocmget (struct tty_struct *tty, struct file *file)
-{
- struct usb_serial_port *port = tty->driver_data;
- unsigned int control;
- int result;
-
- dbg("%s - port %d", __func__, port->number);
-
- cp210x_get_config(port, CP210X_GET_MDMSTS, &control, 1);
-
- result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
- |((control & CONTROL_RTS) ? TIOCM_RTS : 0)
- |((control & CONTROL_CTS) ? TIOCM_CTS : 0)
- |((control & CONTROL_DSR) ? TIOCM_DSR : 0)
- |((control & CONTROL_RING)? TIOCM_RI : 0)
- |((control & CONTROL_DCD) ? TIOCM_CD : 0);
-
- dbg("%s - control = 0x%.2x", __func__, control);
-
- return result;
-}
-
-static int cp210x_carrier_raised(struct usb_serial_port *p)
-{
- unsigned int control;
- cp210x_get_config(p, CP210X_GET_MDMSTS, &control, 1);
- if (control & CONTROL_DCD)
- return 1;
- return 0;
-}
-
-static void cp210x_break_ctl (struct tty_struct *tty, int break_state)
-{
- struct usb_serial_port *port = tty->driver_data;
- unsigned int state;
-
- dbg("%s - port %d", __func__, port->number);
- if (break_state == 0)
- state = BREAK_OFF;
- else
- state = BREAK_ON;
- dbg("%s - turning break %s", __func__,
- state == BREAK_OFF ? "off" : "on");
- cp210x_set_config(port, CP210X_SET_BREAK, &state, 2);
-}
-
-static int cp210x_startup(struct usb_serial *serial)
-{
- /* cp210x buffers behave strangely unless device is reset */
- usb_reset_device(serial->dev);
- return 0;
-}
-
-static int __init cp210x_init(void)
-{
- int retval;
-
- retval = usb_serial_register(&cp210x_device);
- if (retval)
- return retval; /* Failed to register */
-
- retval = usb_register(&cp210x_driver);
- if (retval) {
- /* Failed to register */
- usb_serial_deregister(&cp210x_device);
- return retval;
- }
-
- /* Success */
- printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":"
- DRIVER_DESC "\n");
- return 0;
-}
-
-static void __exit cp210x_exit(void)
-{
- usb_deregister(&cp210x_driver);
- usb_serial_deregister(&cp210x_device);
-}
-
-module_init(cp210x_init);
-module_exit(cp210x_exit);
-
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_VERSION(DRIVER_VERSION);
-MODULE_LICENSE("GPL");
-
-module_param(debug, bool, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(debug, "Enable verbose debugging messages");