New features for cpmfg and cpio.

[cp210x.git] / src / examples / cpio.c

diff --git a/src/examples/cpio.c b/src/examples/cpio.c
index a4f2f7ad24868f1dd1dd759f5aeb89427dba0cb9..b08ee23f7b4b27f16d231cb4cc7aeaa02b21f892 100644 (file)
--- a/src/examples/cpio.c
+++ b/src/examples/cpio.c
@@ -1,8 +1,7 @@
 /**
  * cpio.c
  *
- * Set cp2103 GPIO_0 and GPIO_1 for LED connection to get RX/TX activity.
- * Watch out, the tty is hardcoded.
+ * Configure the and GPIO configuration for a cp2103-equipped device.
  */
 
 #include <netinet/in.h>
@@ -12,31 +11,34 @@
 #include <sys/stat.h>
 #include <fcntl.h>
 
-#define IOCTL_DEVICERESET      0x8004  /* Get port configuration */
+#define IOCTL_DEVICERESET      0x8004  /* Reset the cp210x */
 #define IOCTL_PORTCONFGET      0x8005  /* Get port configuration */
 #define IOCTL_PORTCONFSET      0x8006  /* Set port configuration */
 
+/* Port config definitions */
 typedef struct {
-    uint16_t mode;
+    uint16_t mode;             /* Push-pull = 1, Open-drain = 0 */
     uint16_t lowPower;
-    uint16_t latch;
-} cp2103_port_state_t;
+    uint16_t latch;            /* Logic high = 1, Logic low = 0 */
+} cp2101_port_state_t;
 
 typedef struct {
-    cp2103_port_state_t reset;
-    cp2103_port_state_t suspend;
+    cp2101_port_state_t reset;
+    cp2101_port_state_t suspend;
     uint8_t enhancedFxn;
-} cp2103_port_config_t;
+} cp2101_port_config_t;
+
+void exit(int);
 
 int cpConnect(char* device)
 {
     int ret, ioval;
     int fd = open(device, O_RDWR);
     if (fd < 0) {
-       fprintf(stderr, "cannot open tty\n");
-       return -1;
+       fprintf(stderr, "cannot open %s\n", device);
+       exit(1);
     }
-    printf("tty opened\n");
+    printf("%s opened\n", device);
     return fd;
 }
 
@@ -46,45 +48,78 @@ void cpDisconnect(int fd)
        close(fd);
 }
 
-int main(int argc, char* argv[])
+void cpSetPortConf(int fd, int pullups)
 {
-    int fd;
-    cp2103_port_config_t config;
     int ret;
-
-    if (argc != 2) {
-       fprintf(stderr, "usage: %s <tty>\n", argv[0]);
-       return 1;
-    }
-
-    /* open */
-    if ((fd = cpConnect(argv[1])) < 0)
-       return 1;
+    cp2101_port_config_t config;
 
     /* Read the current port configuration */
     if ((ret = ioctl(fd, IOCTL_PORTCONFGET, &config))) {
        fprintf(stderr, "portconfget ioctl failed %d\n", ret);
-       return 1;
+       exit(1);
     }
 
-    /* Set the current port configuration; turn on GPIO_0 and GPIO_1 to get
-     * activity LEDs.
+    /* This section assumes the device is currently at factory defaults.  If
+     * not, first run 'cpfactory'.  The only delta from factory defaults is to
+     * activate the activity pin functions for GPIOs 0 and 1.  Some boards may
+     * require weak pull-ups, but not TMI's RWS.
+     *
+     * GPIO mapping:
+     *   GPIO_0 -> TX activity, active low
+     *   GPIO_1 -> RX activity, active low
+     *   GPIO_2 -> MSP430 UC_TCK
+     *   GPIO_3 -> MSP430 UC_RST
+     *
      */
-    config.reset.mode &= ~0x0300;
-    config.suspend.mode &= ~0x0300;
-    config.reset.latch |= 0x0300;
-    config.enhancedFxn &= ~0x03;
+    config.reset.mode |= 0x0800; /* GPIO_3 gets push-pull driver */
+    config.enhancedFxn |= (pullups) ? 0x13 : 0x03;
+
     if ((ret = ioctl(fd, IOCTL_PORTCONFSET, &config))) {
        fprintf(stderr, "portconfset ioctl failed %d\n", ret);
-       return 1;
+       exit(1);
     }
+}
+
+void cpReset(int fd)
+{
+    int ret;
 
-    /* Reset the part so the changes take effect. */
+    /* Reset the part */
     if ((ret = ioctl(fd, IOCTL_DEVICERESET, 0))) {
        fprintf(stderr, "device reset ioctl %d\n", ret);
-       return 1;
+       exit(1);
+    }
+}
+
+void usage(char* program)
+{
+    fprintf(stderr, "usage: %s [--pullups] <tty> <mfg> <part#> <sn#>\n",
+       program);
+}
+
+int main(int argc, char* argv[])
+{
+    int fd;
+    int pullups = 0;
+
+    if (argc < 2 || argc > 3) {
+       usage(argv[0]);
+       exit(1);
+    }
+
+    if (argc == 3) {
+       if (strncmp(argv[1], "--p", 3) == 0)
+           pullups = 1;
+       else {
+           usage(argv[0]);
+           exit(1);
+       }
     }
 
+    fd = cpConnect(argv[pullups + 1]);
+    cpSetPortConf(fd, pullups);
+    cpReset(fd);
     cpDisconnect(fd);
+    printf("done\n");
     return 0;
 }